News & Blogs

Position:HOME >> News

Key points for selecting vertical multi-stage centrifugal pumps

From:YangTze River Time:2026/11/9 16:24:43

Vertical multi-stage centrifugal pumps are commonly used in scenarios such as pressure boosting, water supply, water treatment, and industrial transportation. The core of pump selection revolves around three key indicators: flow rate, head, and medium material. At the same time, the working conditions, sealing, motor, and other supporting conditions are combined to determine the selection. This avoids problems such as using a large engine for a small task or insufficient head and flow rate.

vertical multistage centrifugal boosting pump

vertical multistage centrifugal boosting pump

Key points for selecting vertical multi-stage centrifugal pumps

1. Flow rate selection

Flow rate is the basis for pump selection, representing the volume of medium transported per unit time. First, calculate the maximum demand flow rate of the system. For domestic water supply, calculate the peak water consumption based on the simultaneous use coefficient. For HVAC and industrial circulation, take the rated flow rate of the process as the value. It is recommended to reserve 10% to 20% of margin to prevent flow reduction due to pipe scaling and filter blockage; at the same time, ensure that the rated flow rate of the pump is as close as possible to the efficient range of the performance curve and do not operate at a very small flow rate for a long time, otherwise it is prone to overheating, cavitation, and mechanical seal damage.

2. Head selection

Head represents the total ability of the pump to overcome pipeline resistance and lift height. It is not just the simple height lift. Total head = geometric lift height + pipeline along-line resistance + local resistance (tees, valves, filters) + terminal required pressure. Also reserve 10% to 15% margin to avoid insufficient pressure after pipeline aging; for multi-stage pumps, the high head is achieved by the superposition of impellers, and if the head is insufficient, increase the number of stages. However, do not blindly increase the number of stages; too much head margin will lead to actual flow rate exceeding the limit and motor overload.

3. Material selection key points

Material is determined by the medium, temperature, and acidity/alkalinity:

1. Clear water, ordinary domestic water (normal temperature): Pump body 304 stainless steel, impeller guide vanes 304 stainless steel, the most cost-effective and also the most commonly used solution for water supply;
2. Pure water, reverse osmosis, deionized water: Prefer 316L stainless steel, which has lower rusting and less precipitation, meeting water quality requirements;
3. Weak acid and alkali, slightly corrosive wastewater: Can choose 316L, for stronger corrosive media, consider fluorine-lined materials;
4. Water with sand and particles: Select wear-resistant stainless steel or hard alloy friction pairs, ordinary stainless steel is prone to wear;
5. Hot water conditions: In addition to stainless steel, the sealing parts should be replaced with high-temperature resistant fluororubber, and check the material's temperature limit.

Other key points for selecting other components

Sealing is usually divided into mechanical seals. For clear water, the commonly used material is nitrile rubber. For corrosive and high-temperature media, replace with fluororubber; motors are preferred as national standard vertical motors for explosion-proof scenarios; also check the cavitation margin NPSHa to prevent pump cavitation; in variable frequency and pressure-stabilizing water supply scenarios, directly match a variable frequency motor or an external frequency converter.

Summary

For the selection of vertical multi-stage centrifugal pumps, first determine the required flow rate and head based on the actual working conditions, and leave a reasonable margin to ensure the pump operates in the efficient range. Then, match the pump body, impeller, and sealing material according to the corrosiveness of the medium, the presence of particles, and temperature. Finally, choose a regular or explosion-proof motor based on the on-site environment, and also check the cavitation margin. Only when the entire matching is correct can the pump operate stably for a long time, taking into account both energy consumption and service life.

Copyright © ZHEJIANG YANGTZE RIVER PUMP CO.,LTD.All Rights Reserved.
WhatsApp
Skype
Email
Mobile
Online
Online
Email
WhatsApp
WeChat